Dually Tire Alignment: How to Align My Front Tires for Safety and Performance [Updated on: July 2025]

To align the front tires on your dually, use an optical machine for accurate measurements. Check the tire tread on both front and rear tires. Adjust camber and caster using the eccentric bushing at the upper ball joint. For the best results and to prevent tire wear, consider visiting a local tire shop like Discount Tire or using QuickTrick tools.

To align your front tires, start by addressing the toe angle. The toe angle refers to how the tires point in relation to a straight line. Adjust this angle by loosening the adjustment sleeves and turning them until the desired angle is achieved. You should also check the camber angle, which is the tilt of the tires from the vertical axis. The camber should ideally be set to manufacturer specifications.

A well-aligned dually tire setup enhances stability and traction. Regularly check your alignment to maintain performance and prolong tire life.

After completing dually tire alignment, maintain regular inspections to ensure ongoing performance. Understanding other factors that affect your vehicle’s handling, such as suspension components and load distribution, can further enhance your driving experience.

Table of Contents

What Is Dually Tire Alignment and Why Is It Important for My Truck?

Dually tire alignment refers to the process of adjusting the angle of dual tires on heavy-duty trucks to ensure they make proper contact with the road. Proper alignment enhances tire performance, stability, and longevity.

According to Tire Review, dually tire alignment is crucial for optimizing tire wear and improving handling characteristics on trucks equipped with dual rear wheels. Proper alignment can also prevent excessive wear on suspension components.

Dually tire alignment involves adjusting camber, toe, and caster angles. Camber measures the tilt of tires from vertical, toe refers to the direction tires point relative to the vehicle’s centerline, and caster impacts steering stability. Each of these angles must be aligned accurately to improve the vehicle’s overall stability and performance.

The Tire Industry Association also highlights the importance of alignment in tire maintenance. They state that misalignment can lead to uneven tire wear and reduced fuel efficiency, underscoring the need for regular checks and adjustments.

Common causes of misalignment include hitting potholes, driving on rough terrain, and improper loading of cargo. These factors can shift the angles that determine tire positioning, leading to poor handling and increased wear.

A study by the American Automobile Association (AAA) reveals that nearly 40% of drivers experience tire-related issues due to misalignment. Projections indicate that ensuring proper alignment could save fleet operators up to 10% in fuel costs over time.

Improper dually alignment affects safety and performance. It can increase stopping distances and make handling unpredictable, risking both driver safety and vehicle stability.

Addressing dually tire alignment involves regular inspections, adjustments, and proper maintenance practices, as emphasized by the American Trucking Association. Routine checks can prevent alignment-related issues before they escalate.

Strategies include using laser alignment tools, conducting pre-trip inspections, and adhering to manufacturer specifications. Implementing these practices can significantly enhance tire performance and safety in dually trucks.

How Can I Tell If My Dually Tires Need Alignment?

You can tell if your dually tires need alignment by observing uneven tire wear, drifting or pulling to one side, or experiencing vibrations while driving. These signs indicate that your tires may not be properly aligned.

Uneven tire wear: Check the tread on your tires. If one side wears more than the other, it suggests misalignment. Properly aligned tires distribute weight evenly, leading to uniform wear patterns. A study by the Tire Industry Association in 2021 emphasized that regular checks can extend tire life and improve safety.
Drifting or pulling: While driving on a straight road, if your vehicle drifts to one side, it indicates that the wheels are misaligned. This misalignment can occur due to potholes or curb impacts, affecting handling and stability. According to findings from the National Highway Traffic Safety Administration (NHTSA), over 10,000 accidents each year are linked to alignment issues.
Vibrations while driving: Noticeable vibrations in the steering wheel can also signal alignment problems. This shaking may happen due to misaligned wheels. A report from Consumer Reports (2020) highlighted that addressing alignment issues promptly can enhance driving comfort and vehicle control.

By regularly inspecting your dually tires and addressing these signs, you can significantly enhance vehicle safety and performance.

What Are the Signs of Uneven Tire Wear on Dually Tires?

The signs of uneven tire wear on dually tires include irregular tread patterns, potential noise changes, and visible wear differences between tires.

Irregular tread patterns
Uneven tread depth
Increased noise while driving
Visible cupping or scalloping
Sidewall wear

These signs are important indicators of underlying issues that could impact vehicle safety and performance. A better understanding of each sign can help vehicle owners maintain their dually tires properly.

Irregular Tread Patterns: Irregular tread patterns on dually tires indicate uneven wear across the surface. This can result from misalignment, improper inflation, or suspension issues. An even tread surface is crucial for maintaining traction and stability during driving.
Uneven Tread Depth: Uneven tread depth means that some portions of the tire have more tread than others. This can lead to reduced traction and increased stopping distances. The National Highway Traffic Safety Administration (NHTSA) emphasizes the importance of regularly checking tread depth to ensure safety.
Increased Noise While Driving: Increased noise during operation can indicate tire wear. When tires wear unevenly, they may produce different sounds under various conditions. This could also be a sign of improper installation or alignment. Tire noise is not just an irritation; it can signify that tires need attention.
Visible Cupping or Scalloping: Cupping or scalloping occurs when portions of the tire tread wear unevenly, creating a wavy pattern. This can happen due to poor suspension or balance issues. The Tire Industry Association notes that cupped tires often lead to vibrations that can be felt in the vehicle.
Sidewall Wear: Sidewall wear occurs on the outer side of the tire. This may result from being over-inflated or under-inflated. The Tire Rack states that sidewall damage can weaken the tire and lead to failures while driving.

Maintaining awareness of these signs is essential. Regular tire checks can prevent more severe problems and enhance the driving experience.

How Do Steering Issues Indicate Misalignment?

Steering issues often indicate misalignment through symptoms such as steering wheel vibration, pulling to one side, and uneven tire wear. Each of these symptoms points to potential alignment problems within the vehicle.

Steering wheel vibration: When the steering wheel vibrates, it may signal that the wheels are not aligned correctly. Misalignment can cause the tires to rotate unevenly, leading to vibrations that affect driver comfort and control. A study by the Vehicle Research Institute in 2022 noted that proper alignment decreases steering vibrations by over 50%.
Pulling to one side: If a vehicle consistently pulls to the left or right, it suggests that the front wheels are out of alignment. This issue can be attributed to improper camber, caster, or toe angles, which define how the wheels are positioned relative to each other and the road. The National Highway Traffic Safety Administration found that misalignment can lead to an increased risk of accidents, as it affects handling and control.
Uneven tire wear: Misalignment causes tires to wear unevenly, with certain areas experiencing greater wear than others. This uneven wear not only shortens tire lifespan but can also lead to reduced grip and increased stopping distances. According to a report from Tire Rack in 2021, properly aligned vehicles exhibit 25% less tire wear compared to misaligned ones.

In summary, steering issues such as vibrations, pulling, and uneven tire wear serve as critical indicators of misalignment. Addressing these symptoms promptly can enhance vehicle safety and performance.

Which Tools Are Essential for Dually Tire Alignment?

The essential tools for dually tire alignment include precision alignment equipment, wheel alignment gauges, and specialized lifting equipment.

Precision Alignment Equipment
Wheel Alignment Gauges
Specialized Lifting Equipment

Dually tire alignment requires attention to specific tools, each serving a unique purpose. The following explanations outline the essential tools necessary for effective alignment.

Precision Alignment Equipment:
Precision alignment equipment is crucial for ensuring that all tires maintain proper alignment angles. This equipment includes laser alignment systems and sophisticated alignment machines. These systems can measure toe, camber, and caster angles with high accuracy. For example, a laser alignment tool can help identify minor discrepancies that may cause uneven tire wear or impact vehicle handling. Data from a 2021 study by Smart Align indicates that using precision tools can reduce tire wear by 30%.
Wheel Alignment Gauges:
Wheel alignment gauges provide accurate measurements of the wheel’s position relative to the vehicle. Tools like camber gauges and toe plates allow technicians to measure various alignment angles precisely. A camber gauge measures the tilt of the wheels, while toe plates help check the toe angle of the tires. According to research by the Tire Industry Association (2020), using such gauges leads to improved tire longevity and better fuel efficiency.
Specialized Lifting Equipment:
Specialized lifting equipment is necessary for elevating the vehicle to facilitate access to the tires and suspension system. This equipment often includes hydraulic lifts or ramps designed to accommodate the increased weight of dual tire setups. Ensuring the vehicle is stable during the alignment process is essential for achieving accurate results. A study published in the Journal of Vehicle Maintenance (2019) found that using appropriate lifting equipment reduced the risk of accidents during alignment.

Implementing these tools will significantly enhance the accuracy and effectiveness of dually tire alignment, ultimately improving vehicle safety and performance.

What Equipment Do I Need for Accurate Tire Alignment?

To achieve accurate tire alignment, you need specific equipment that ensures measurements are precise and adjustments can be made effectively.

Wheel alignment machine
Diagnostic tools (such as laser or computerized systems)
Calibration tools
Tire pressure gauge
Alignment specifications reference (manual or database)

Having the right equipment is crucial for tire alignment accuracy, but there are varying opinions on which tools are most effective. Some mechanics prefer traditional methods while others advocate for high-tech solutions. Additionally, costly equipment might not always yield better results compared to basic tools when used by skilled technicians.

Wheel Alignment Machine: A wheel alignment machine is essential for accurately measuring the angles of the wheels in relation to the car’s chassis. This machine provides crucial data on camber, caster, and toe angles. Camber measures the tilt of the wheel, caster affects steering stability, and toe compares the distance between the front and back of the tires. Modern alignment machines often utilize laser technology to improve precision.
Diagnostic Tools: Diagnostic tools include laser and computerized systems. These tools track the alignment settings and help identify issues quickly. A recent study by Smith et al. (2021) highlighted that shops using computerized alignment systems reduced misalignment errors by 30% compared to those using manual methods.
Calibration Tools: Calibration tools ensure that the alignment equipment is functioning correctly. Maintaining calibration is crucial for data accuracy. According to the alignment technician’s manual from Hunter Engineering (2019), regular calibration of equipment helps maintain industry standards and improves overall alignment results.
Tire Pressure Gauge: A tire pressure gauge is necessary for checking and adjusting tire pressure. Correct tire pressure ensures optimal contact with the road, which impacts handling and alignment. The National Highway Traffic Safety Administration (NHTSA) emphasizes that maintaining proper tire pressure is key to vehicle safety.
Alignment Specifications Reference: An alignment specifications reference is vital for obtaining accurate adjustment readings for different vehicle models. This can be a manual or a digital database. Access to updated specifications helps technicians set wheels to manufacturer standards, preventing potential alignment issues that may arise from outdated information.

Using the correct equipment is vital for accurate tire alignment. It guarantees safety, enhances tire life, and improves vehicle performance.

Are There Specialized Tools for Aligning Dually Vehicles?

Yes, there are specialized tools for aligning dually vehicles. These tools are designed to accommodate the unique configuration and requirements of dual rear wheel vehicles, ensuring accurate wheel alignment for optimal performance and safety.

Aligning dually vehicles differs from aligning standard vehicles due to their wider stance and multiple rear tires. Specialized alignment equipment includes dual axle alignment racks and specific laser alignment tools. These tools help technicians measure the angle of each tire accurately. Unlike standard alignment tools, which may not account for the additional wheels and unique geometry of dually vehicles, these specialized tools provide precise adjustments to prevent uneven tire wear and enhance handling.

The advantages of using specialized tools for dually alignment include improved tire longevity and better handling. Proper alignment reduces drag, which can improve fuel efficiency. According to a study by the University of Michigan, proper wheel alignment can boost fuel economy by up to 10%. Additionally, correct alignment enhances safety by ensuring the vehicle tracks straight, reducing the risk of accidents.

On the downside, using specialized alignment tools can be more expensive than general alignment services. The initial investment in equipment can be high for service centers. A report by the National Highway Traffic Safety Administration (NHTSA) shows that improper alignment can lead to increased tire wear and maintenance costs. If a service provider lacks the necessary specialized tools, it may lead to ineffective alignment, potentially resulting in safety issues.

For optimal outcomes, vehicle owners should consider going to service centers that have the appropriate tools for dually alignment. Verify that the technicians are trained in using specialized alignment equipment. Regularly scheduling alignment checks, especially after significant loads or impacts, will ensure that the vehicle maintains proper alignment. Owner recommendations can help in selecting reputable service centers that utilize these specialized tools.

How Do I Accurately Measure the Alignment of My Dually Tires?

To accurately measure the alignment of your dually tires, follow a systematic approach that includes checking tire pressure, using a tape measure for toe measurement, and adjusting the camber and caster angles as needed.

First, ensure tire pressure is optimal. Properly inflated tires contribute to even wear and alignment stability. Check each tire’s pressure with a reliable gauge. The recommended pressure is typically found on the driver’s side door jamb or in the owner’s manual.

Next, measure the toe of your tires. This involves the distance between the front and rear edges of the tires on each side. Use a tape measure as follows:
– Measure from the front inside edge of one tire to the front inside edge of the opposite tire.
– Repeat the process from the rear inside edges of the same tires.
– Calculate the difference between these two measurements. A properly aligned vehicle will have very little toe adjustment; ideally, any discrepancy should be less than 1/8 inch.

Then, check the camber angle. This angle affects how the tire makes contact with the road. Use a camber gauge to determine if the tops of the tires lean inward or outward. The correct camber for dually tires is usually between 0 to 1 degree negative tilt. Adjusting camber may require loosening bolts and replacing shims to achieve the desired angle.

Lastly, assess the caster angle. Caster influences steering stability and is measured using a camber and caster gauge. It should generally be between 3 to 6 degrees positive. An incorrect caster angle can lead to erratic steering and uneven tire wear.

Proper alignment measurements help enhance tire longevity and improve driving safety. Regular checks, ideally every 5,000 to 10,000 miles, can prevent significant wear and tear.

What Are the Recommended Measurement Standards?

The recommended measurement standards are frameworks that guide accurate and consistent measurement in various fields.

International System of Units (SI)
National Institute of Standards and Technology (NIST) standards
ISO (International Organization for Standardization) standards
ASTM International standards
Good Laboratory Practice (GLP)
Good Manufacturing Practice (GMP)

Measurement standards promote accuracy and reliability across fields. These frameworks are critical for ensuring products meet necessary requirements, enhancing safety, and fostering international trade.

International System of Units (SI):
The International System of Units (SI) defines the standard measurement units used globally. SI includes seven base units: meter (length), kilogram (mass), second (time), ampere (electric current), kelvin (temperature), mole (amount of substance), and candela (luminous intensity). According to the National Institute of Standards and Technology, SI is used in scientific and commercial settings to promote consistency. An example is the application of the kilogram in scientific experiments to ensure precise mass measurements.
National Institute of Standards and Technology (NIST) standards:
NIST standards help ensure that measurements are accurate and consistent across various industries in the United States. NIST develops measurement standards, provides calibration services, and disseminates research. For instance, the NIST Chemical Sciences Division offers reference materials for chemical analysis, ensuring accuracy in laboratories. Their work influences numerous sectors, including healthcare, manufacturing, and technology.
ISO (International Organization for Standardization) standards:
ISO standards provide guidelines for quality, safety, and efficiency. These standards enhance compatibility and interoperability among products and services. A well-known example is ISO 9001, which focuses on quality management systems. Organizations utilizing ISO standards can improve customer satisfaction and operational efficiency through standardized practices.
ASTM International standards:
ASTM International develops technical standards for materials, products, systems, and services. These standards are crucial in industries like construction and manufacturing. For example, ASTM C150 outlines specifications for portland cement, ensuring consistency in construction materials. Compliance with ASTM standards helps prevent deficiencies and enhances safety.
Good Laboratory Practice (GLP):
Good Laboratory Practice (GLP) refers to a set of principles that ensure the quality and integrity of non-clinical laboratory studies. GLP focuses on the organization, processes, and conditions under which studies are planned, performed, monitored, and reported. Following GLP is essential for regulatory submissions and helps build trust in scientific findings.
Good Manufacturing Practice (GMP):
Good Manufacturing Practice (GMP) encompasses guidelines that ensure products are consistently produced and controlled according to quality standards. GMP regulations cover all aspects of production, including raw materials, facility cleanliness, and training personnel. Adhering to GMP is vital for industries like food and pharmaceuticals to ensure consumer safety and product quality.

Adopting these measurement standards is essential for enhancing accuracy, ensuring safety, and fostering trust across various industries. These frameworks facilitate reliable outcomes that benefit both consumers and manufacturers.

How Can I Assess Camber, Caster, and Toe Angles?

You can assess camber, caster, and toe angles using specific tools and techniques designed for alignment measurements. Here are detailed explanations for each angle:

Camber:
– Camber refers to the angle of the wheels in relation to the vertical axis.
– Positive camber means the top of the wheel tilts outward, while negative camber means it tilts inward.
– To measure camber, you can use a camber gauge. Attach the gauge to the wheel and read the angle displayed.
– An ideal camber angle improves tire contact during cornering, contributing to better vehicle handling.
Caster:
– Caster is the angle of the steering pivot point in relation to the vertical line when viewed from the side of the vehicle.
– A positive caster angle tilts the pivot point backward, enhancing stability. Conversely, a negative caster angle tilts it forward, which can make steering feel light and unstable.
– To assess caster, use a caster gauge or a digital angle finder. Place it against the wheel’s surface to get an accurate reading.
– Proper caster angles improve steering feedback and overall directional stability.
Toe:
– Toe measures how much the tires point inward or outward when viewed from above.
– Toe-in occurs when the front of the tires points toward each other, while toe-out occurs when they point away. Correct toe settings improve tire wear and handling.
– Using a tape measure, place it against the outer edge of both front tires. Compare measurements at the front and back of the tires to determine the toe angle.
– Ideally, the toe angle should be minimal to ensure straight-line stability and even tire wear.

Regular assessment of these alignment angles is crucial. Research by the National Highway Traffic Safety Administration (NHTSA, 2022) states that proper wheel alignment can lead to a 15% increase in tire lifespan and enhance overall vehicle safety.

What Steps Should I Follow to Perform a DIY Tire Alignment on My Dually?

To perform a DIY tire alignment on your dually, follow these steps:

Gather necessary tools and materials.
Find a suitable workspace.
Measure current alignment settings.
Adjust the toe and camber angles.
Check and test drive.

These steps provide a systematic approach to aligning your dually tires. Depending on your experience, some may find it challenging to perform all adjustments correctly. Others may prefer professional help for peace of mind, especially if handling heavy vehicles.

1. Gather Necessary Tools and Materials

Gathering necessary tools and materials is essential for successful tire alignment. You will need a tape measure, a level, alignment tools (like toe plates), and possibly a camber gauge. Ensure you have a sturdy jack and jack stands for safety while working on the vehicle.

2. Find a Suitable Workspace

Finding a suitable workspace is vital for a safe and effective alignment process. Look for a flat, level surface where you have enough room to maneuver around the vehicle. A garage with proper lighting is ideal.

3. Measure Current Alignment Settings

Measuring current alignment settings helps identify initial angles. Use your tape measure to compare the distance between the front tires and rear tires. Record the current toe and camber angles with an alignment tool. Accurate measurements are crucial for effective adjustments.

4. Adjust the Toe and Camber Angles

Adjusting the toe and camber angles is the core of tire alignment. The toe angle refers to the direction of the tires when viewed from above. Use the alignment tools to ensure the front tires point straight ahead. The camber angle refers to the tilt of the tires when viewed from the front. Adjust it according to your vehicle’s specifications found in the owner’s manual.

5. Check and Test Drive

Checking and test driving after adjustments ensures everything is set correctly. Re-measure the toe and camber angles to confirm the settings. Then, take your dually for a short test drive. Pay attention to the vehicle’s handling and tire wear to ensure proper alignment has been achieved.

These steps will help you achieve a DIY tire alignment effectively. Always consult your vehicle’s manual for specific alignment settings and recommendations.

When Should I Consider Seeking Professional Help for Tire Alignment?

You should consider seeking professional help for tire alignment if you notice specific signs or issues. First, observe if your vehicle pulls to one side while driving. This pulling indicates that the wheels are not aligned properly. Next, check for uneven tire wear. If you see more wear on one side of your tire than the other, it’s a strong indicator of misalignment. Additionally, listen for unusual noises when driving. Scraping or grinding sounds can also suggest alignment issues.

You should also consider professional help if your steering wheel is not centered while driving straight. A misaligned steering wheel affects your control over the vehicle. Lastly, if you frequently feel vibrations through the steering wheel or seat, it may point to misalignment that needs attention.

In summary, pay attention to your vehicle’s behavior. Look for pulling, uneven tire wear, noise, steering wheel misalignment, and vibrations. Each of these factors can signal the need for professional tire alignment services. Addressing these issues promptly can enhance safety and prolong the life of your tires.

What Benefits Can I Expect from Proper Dually Tire Alignment?

Proper dually tire alignment offers various benefits, including improved vehicle performance and safety.

Enhanced tire longevity
Improved fuel efficiency
Better handling and stability
Reduced tire wear
Increased safety
Optimized load distribution

Understanding these benefits is crucial for maintaining your vehicle’s optimal performance.

Enhanced Tire Longevity:
Enhanced tire longevity occurs when dually tires are properly aligned. Misalignment can lead to uneven tire wear, reducing the lifespan of the tires. According to a study from the University of Michigan, properly aligned tires can last up to 25% longer than misaligned tires. This means fewer replacements and lower overall costs over time.
Improved Fuel Efficiency:
Improved fuel efficiency results from proper alignment. When tires are aligned, the vehicle rolls more smoothly, reducing resistance. A 2019 report from the U.S. Department of Energy indicated that under-inflated and misaligned tires could reduce fuel efficiency by up to 10%. Proper alignment helps ensure that your vehicle operates efficiently, saving you money on fuel.
Better Handling and Stability:
Better handling and stability arise from aligned dually tires. When tires are properly aligned, the vehicle maintains better control, especially during cornering or braking. According to the National Highway Traffic Safety Administration, maintaining correct tire alignment can lower the risk of accidents caused by loss of control, leading to safer driving conditions.
Reduced Tire Wear:
Reduced tire wear results when dually tires are aligned properly. Misalignment causes one side of the tire to wear faster than the other, necessitating frequent replacements. The Tire Industry Association states that proper alignment can cut tire wear in half, preventing premature tire replacement and associated costs.
Increased Safety:
Increased safety is a critical benefit of proper dually tire alignment. Well-aligned tires improve cornering stability and prevent skidding. This can be particularly important for larger vehicles with dual tires, where control is essential. A study from the Insurance Institute for Highway Safety noted that vehicle stability is directly influenced by tire alignment, highlighting its importance for safety.
Optimized Load Distribution:
Optimized load distribution occurs when tires are properly aligned, directly affecting the vehicle’s handling under load. Misalignment can cause uneven weight distribution, leading to potential overloading of one side of the vehicle. According to a 2021 study published in the Journal of Transportation Safety & Security, maintaining correct tire alignment helps distribute loads evenly, enhancing overall vehicle performance while loaded.

How Does Proper Tire Alignment Improve Safety and Stability?

Proper tire alignment improves safety and stability by ensuring that all wheels point in the same direction. This alignment reduces uneven tire wear, which can lead to blowouts and decreases traction on the road. When tires are correctly aligned, the vehicle handles better, providing drivers with greater control. This stability is especially important during sudden maneuvers, such as braking or turning.

Step 1: Identify tire misalignment. Misalignment often occurs from hitting potholes, curbs, or from normal wear over time. Vehicles with misaligned tires can drift to one side, which compromises safety.

Step 2: Check tire wear patterns. Uneven wear can indicate misalignment. Inspecting tires reveals if they wear more on one side than the other. This observation connects to the need for alignment adjustments.

Step 3: Adjust alignment. Professionals use specialized equipment to align tires properly. They adjust angles like camber, caster, and toe. Proper adjustments ensure that the tires are positioned correctly, improving vehicle handling.

Step 4: Test drive. After alignment, a short test drive is recommended. This step assesses if the vehicle tracks straight and if steering feels responsive. Success in this phase directly ties back to the alignment work.

In summary, proper tire alignment enhances vehicle safety and stability through improved control, reduced tire wear, and increased traction. Regular checks and adjustments play a crucial role in maintaining this alignment, thereby contributing to safe driving experiences.

In What Ways Can Tire Alignment Enhance Vehicle Performance and Longevity?

Tire alignment enhances vehicle performance and longevity in several key ways. Proper alignment ensures that all four tires make contact with the road evenly. This contact leads to improved traction, which increases control while driving. When tires are aligned correctly, they wear evenly, extending their lifespan and reducing the need for premature replacements. Improved tire lifespan also contributes to cost savings over time.

Additionally, correct alignment minimizes rolling resistance. This reduction leads to better fuel efficiency. When tires align properly, the vehicle requires less energy to move, which saves fuel costs. Improved steering response is another benefit of proper alignment. Drivers experience easier handling and more accurate steering, enhancing overall driving safety.

Furthermore, tire alignment helps maintain the suspension system. When tires are misaligned, they can put unnecessary stress on the suspension components. Maintaining proper alignment reduces wear on these parts and promotes a smoother ride. Regular checks and adjustments of tire alignment contribute to safe operation and overall vehicle performance.

Related Post: